Peugeot 208 Key Replacement
It is best to leave the replacement of Peugeot keys 208 to auto locksmiths with the equipment and expertise. They can design and program keys more quickly and at a lower cost than dealerships.
A dead battery for your coin is the most likely cause the reason why your key fob isn't locking or unlocking doors. However, there are other possibilities that the key is malfunctioning.
Dead Coin Battery
A dead battery in the coin compartment will prevent your Peugeot 208 from locking or unlocking, and will not start the engine. If this is the case, you'll need to utilize the backup starting method that is detailed in the owner's manual to your vehicle.
Another reason why the 208 won't start is that the spark plugs are been damaged. The spark plugs are responsible to ignite the fuel which starts the engine. They have a limited life span. They'll eventually degrade if they're not used enough.
There is a simple solution for this problem. Examine the voltage of your battery using a multimeter. If the voltage is less than 11,5 volts, it's time to replace it. If the battery has corroded it is essential to clean its contacts. You can do this by lifting the rubber covers covering the two battery terminals and using wire brushes to clean any corroded areas of the battery. Then, reconnect the positive and negative pole cables.
Water Damage
If your 208 doesn't start and the battery has not failed, you should inspect the spark plugs. You might find that they are simply too dirty and do not spark. This can be fixed easily by cleaning the spark plugs in the workshop.
peugeot replacement key fob use transponder keys that works with the car's ignition system. This ensures that only a valid key is able to turn the engine. If the chip in the Peugeot key is damaged, it will not send the correct signal to the vehicle.
Water damage is a common cause of this problem. This is a common issue in more cold climates where the car has been exposed to snow or rain. In this case, you need to contact a trusted locksmith who has the necessary tools and equipment to modify the key. They also have the most up-to-date technology and the machinery needed to make the Peugeot 208 smart key. The process should take no more than 15 minutes.
Contacts with the battery may be damaged.
Peugeot replaced the old transponder chips by introducing a new model that is based on electronic components that are mounted on a circuit board. This new system works well when it's new, but as time passes, the circuit boards start to deteriorate and stop working correctly.
This could prevent the immobiliser chip from activating and causing your car to not start. If this is the case it's best to get in touch with a Peugeot specialist or locksmith.
Another issue that is common is when the battery of the key fob begins to fail, which causes the key blade to stop getting into the lock. A locksmith in your car will replace the battery and then cut a new key blade for you. This is a simple fix.
Faulty Receiver Module
If your Peugeot key fob has stopped working after dropping it on the floor, getting exposed to a sudden rain or accidently washing it or washing it, it could be due to a defective receiver module. The receiver is responsible for sending radio frequency signals to an on-board computer which controls the centralized locking system inside your Peugeot vehicle.
Rubber seals on the key fob stop water from getting to the electronic chip. However, prolonged exposure to water can cause damage to these seals and the chip. The high salt content of the ocean water or pool can cause damage to the key fob, especially if it is submerged.
The module will have to be replaced if the Peugeot spare key no longer works. This is only performed by a professional auto locksmith or Peugeot specialist. Like other automobiles, Peugeot keys are protected by an immobilizer that is unique and requires the correct programming in order to start the engine. This is why it is imperative that you should only rely on the Peugeot locksmith to create and program a replacement.
Computers with faulty on-board computers
The computer on board of your Peugeot is responsible for various systems in your car, including power windows and airbags. If something is wrong with these systems, it will usually show a code that identifies the issue. This code will be stored within the system until the problem is resolved. Usually, this will mean the on-board computer being replaced.
One of the most frequent reasons for the airbag light turning on is loose or corroded connections within the airbag sensor. This can be caused by wear and tear, age or exposure to salt and moisture. This issue should be addressed as soon you can, since an airbag malfunctioning could pose a risk in the event in the event of an accident.
If your Peugeot is showing a card not detected error, then the key battery in the key fob may be dead or weak. This will prevent the key fob from sending a signal that disarms the standard immobilizer in your vehicle. You can test this by pressing the unlock button on the key fob and then attempting to start your vehicle. If this does not work then the battery in the key must be replaced.